Login to Your Account

# sau94

#### Ee interview question

###### Rate this Entry
by , 4th March 2015 at 08:30 PM (87 Views)
EE INTERVIEW QUESTION
1. What is a System?When a number of elements or components are connected in a sequence to perform a specificfunction, the group of elements that all constitute a System2. What is Control System?In a System the output and inputs are interrelated in such a manner that the output quantity orvariable is controlled by input quantity, then such a system is called Control System.The output quantity is called controlled variable or response and the input quantity is calledcommand signal or excitation.3. What are different types of Control Systems?Two major types of Control Systems are 1) Open loop Control System 2) Closed Loop ControlSystemsOpen loop Control Systems:The Open loop Control System is one in which the Output Quantityhas no effect on the Input Quantity. No feedback is present from the output quantity to the inputquantity for correction.Closed Loop Control System:The Closed loop Control System is one in which the feedback isprovided from the Output quantity to the input quantity for the correction so as to maintain thedesired output of the system.4. What is a feedback in Control System?The Feedback in Control System in one in which the output is sampled and proportional signalis fed back to the input for automatic correction of the error ( any change in desired output) forfuther processing to get back the desired output.5. Why Negative Feedback is preffered in the Control System?The role of Feedback in control system is to take the sampled output back to the input andcompare output signal with input signal for error ( deviation from the desired result). Negative Feedback results in the better stability of the system and rejects any disturbancesignals and is less sensitive to the parameter variations. Hence in control systems negativefeedback is considered. 6. What is the effect of positive feedback on stability of the system?Positive feedback is not used generally in the control system because it increases the errorsignal and drives the system to instability. But positive feedbacks are used in minor loopcontrol systems to amplify certain internal signals and parameters7. What is Latching current?Gate signal is to be applied to the thyristor to trigger the thyristor ON in safe mode. When thethyristor starts conducting the forward current above the minimum value, called Latchingcurrent, the gate signal which is applied to trigger the device in no longer require to keep the scrin ON position.8. What is Holding current ?When scr is conducting current in forward conduction state, scr will return to forward blockingstate when the anode current or forward current falls below a low level called Holding currentNote: Latching current and Holding current are not same. Latching current is associated withthe turn on process of the scr whereas holding current is associated with the turn off process.In general holding current will be slightly lesser than the latching current.9. Why thyristor is considered as Charge controlled device?During the triggering process of the thyristor from forward blocking state to forward conductionstate through the gate signal, by applying the gate signal (voltage between gate and cathode)increases the minority carrier density in the p-layer and thereby facilitate the reverse break overof the junction J2 and thyristor starts conducting. Higher the magnitude of the gate currentpulse, lesser is the time required to inject the charge and turning on the scr. By controlling theamount of charge we can control the turning on time of the scr.10. What are the different losses that occur in thyristor while operating?Different losses that occur area)Forward conduction losses during conduction of the thyristorb)Loss due to leakage current during forward and reverse blocking.c)Power loss at gate or Gate triggering loss. d)Switching losses at turn-on and turn-off.11. What is meant by knee point voltage?Knee point voltage is calculated for electrical Current transformers and is very important factorto choose a CT. It is the voltage at which a CT gets saturated.(CT-current transformer).12. What is reverse power relay?1.4k LikeSpectrumon the GoContinuousRF Recordand PlaybackCompactportableintegratedsystemPlacement Papers Aptitude Preparation Interview Preparation General Knowledge Online Test Buy NowReverse Power flow relay are used in generating stations's protection. A generating stations issupposed to fed power to the grid and in case generating units are off,there is no generation inthe plant then plant may take power from grid. To stop the flow of power from grid to generatorwe use reverse power relay.13. What will happen if DC supply is given on the primary of a transformer?Mainly transformer has high inductance and low resistance.In case of DC supply there is noinductance ,only resistance will act in the electrical circuit. So high electrical current will flowthrough primary side of the transformer.So for this reason coil and insulation will burn out.14. What is the difference between isolators and electrical circuit breakers? What is bus-bar?Isolators are mainly for switching purpose under normal conditions but they cannot operate infault conditions .Actually they used for isolating the CBs for maintenance. Whereas CB getsactivated under fault conditions according to the fault detected.Bus bar is nothing but ajunction where the power is getting distributed for independent loads.15. What are the advantage of free wheeling diode in a Full Wave rectifier?It reduces the harmonics and it also reduces sparking and arching across the mechanicalswitch so that it reduces the voltage spike seen in a inductive load.16. Mention the methods for starting an induction motor?The different methods of starting an induction motor:a)DOL:direct online starterb)Star delta starterc)Auto transformer starterd)Resistance startere)Series reactor starter17. What is the power factor of an alternator at no load?At no load Synchronous Impedance of the alternator is responsible for creating angledifference. So it should be zero lagging like inductor.18. What is the function of anti-pumping in circuit breaker?When breaker is close at one time by close push button,the anti pumping contactor prevent reclose the breaker by close push button after if it already close.19. What is stepper motor.what is its uses?Stepper motor is the electrical machine which act upon input pulse applied to it. it is one type ofsynchronous motor which runs in steps in either direction instead of running in completecycle.so, in automation parts it is used.20. There are a Transformer and an induction machine. Those two have the same supply. Forwhich device the load current will be maximum? And why?The motor has max load current compare to that of transformer because the motor consumesreal power.. and the transformer is only producing the working flux and its not consuming..hence the load current in the transformer is because of core loss so it is minimum.21. What is SF6 Circuit Breaker?SF6 is Sulpher hexa Flouride gas.. if this gas is used as arc quenching medium in aCircuitbreaker means SF6 CB.22. What is ferrantic effect?Output voltage is greater than the input voltage or receiving end voltage is greater than thesending end voltage.23. What is meant by insulation voltage in cables? explain it?It is the property of a cable by virtue of it can withstand the applied voltage without rupturing itis known as insulation level of the cable.24. What is the difference between MCB & MCCB, Where it can be used?MCB is miniature circuit breaker which is thermal operated and use for short circuit protectionin small current rating circuit. MCCB moulded case circuit breaker and is thermal operated forover load current and magnetic operation for instant trip in short circuit condition.under voltageand under frequency may be inbuilt. Normally it is used where normal current is more than100A.25. Where should the lighting arrestor be placed in distribution lines?Near distribution transformers and out going feeders of 11kv and incomming feeder of 33kvand near power transformers in sub-stations.
THANK YOU..
Categories
Uncategorized

## Trackbacks

Total Trackbacks 0

Send Birthday Wish
Send Birthday Wish
• PRAVIR KUMAR

• Branch : Electronics Engineering

chinniponni

• vilaschavan

• amarmishra2392

• pratikjoshi

• Branch : THIS DOES NOT APPLY ON ME!

akhilanm

• Branch : Computer Science Engineering

Prateek1264

• Branch : Electrical Engineering

srisasanka

• Branch : Computer Science Engineering

praveensonare

• Branch : Computer Science Engineering

virendra2011

• vrajendra upadhyay

• shahidpm

• mekonnenf

• Ambition

• anilbavaliya

• haris98

• subhrakantaroy

• nguyenthanh8822

• jansgiray

• randeep05

• Branch : Electronics Engineering

rupeshj

• shailesh mgr

• Branch : THIS DOES NOT APPLY ON ME!

gucchi_002

• ka0060311

• sabby

• Branch : Civil Engineering

Rohitsaini0022

• x_zenia

• Branch : Computer Science Engineering

ashwini k m

• bhargava

• saurabhgolani

• gaurav loten

• bekarengineer

• Branch : Electronics Engineering

anandsharma290

• fundoosarthak

• Branch : Mechanical Engineering

vtewarii

• amar deep

• Branch : Electronics Engineering

anjula

• Branch : Some other branch

young

• satishkumar

• Branch : Some other branch

young

• raghushri

• Nocksville

• sudhanshu

• vishaldixit

• dpk0208

• radhaakula

• Branch : Information Technology Engineering

bluelord

• antha

• Divya Mallya

• ema_gr8

• AKS021186

• rajwanti meena

• minesh

• d.sri6365

• brijesh yadav

• asim

• maddy.ax

• bluegene

• ZOHAIB SARWAR

• cookingnoob

• thewild

• aayush agarwal

• ekramwaris

• Branch : THIS DOES NOT APPLY ON ME!

ajlooser

• aritra adak

• Branch : Electrical Engineering

rahul551

• anujstillwaiting4u

• Branch : Mechanical Engineering

papamike

• amaraj

• Branch : Electronics Engineering

varun1994

• Branch : Computer Science Engineering

alokvrm02

• vikas4474

• blackhawk

• Branch : Computer Science Engineering

lovely mishra

• affvewfe

• gojja

• chronicles

• Branch : Electrical Engineering

sunny shashank

• teenareddy

• satishkumar343

• sridherreddy42

• rajdanger

• sampath yadav

• Branch : Electronics Engineering

emburey

• Branch : Computer Science Engineering

ipscse

• scoefield

• Branch : Electronics Engineering

ranjandahal

• Branch : Information Technology Engineering

pratikjivani

• Branch : Electrical Engineering

awiey87

• Branch : Electronics Engineering

komaltaliyan

• ankur4u007

• Branch : Some other branch

mic20m

• aniru

• Branch : Aeronautical Engineering

jwfeuihguwihgtuihweguihwe

• Branch : Computer Science Engineering

saurabh09minicomp

• manoharpatil

• c196669

• Branch : Mechanical Engineering

sudeep012

• Branch : Computer Science Engineering

vikashkuriya

• kishan

×